BXDMF - KEL-GUARD EPOXY REDUCER, 25

  • MSDS: BXDMF
  • Manufacturer: KELLY MOORE PAINT CO INC
  • Product Name: KEL-GUARD EPOXY REDUCER, 25
  • National Stock Number: 8010-00N058744
Product Identification

Product ID:KEL-GUARD EPOXY REDUCER, 25
MSDS Date:01/06/1986
FSC:8010
NIIN:00N058744
MSDS Number: BXDMF

Responsible Party
KELLY-MOORE PAINT CO, INC
1015 COMMERCIAL ST
SAN CARLOS, CA 94070
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 415-592-8337

Cage: 0BBH6

Contractor
KELLY-MOORE PAINT CO INC
SAN CARLOS, CA 94070 US

Telephone: 415-592-8337

Cage: 0BBH6

Ingredients

1.2

Fraction By Weight: 20%

OSHA PEL N/K

ACGIH TLV: 100 PPM (MFR)


1.27 @ 93C

Fraction By Weight: 50%

OSHA PEL N/K

ACGIH TLV: 150 PPM (MFR)


ETHANOL, 2-ETHOXY-, ACETATE; (ETHYLENE GLYCOL MONOETHYL

CAS: 111-15-9

RTECS: KK8225000

Fraction By Weight: 30%

OSHA PEL N/K

ACGIH TLV: 50 PPM (MFR)

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:DIZZY, HDCH, NAUSEA, CONFUSION,
IRRIT TO UPPER RESP TRACT, UNCONSCIOUSNESS, SKIN & EYE IRRIT.
CHRONIC:BASED ON STUDIES W/LAB ANIMALS, EGMEEA MAY CAUSE ADVERSE
EFFECTS ON BLOOD & HEMATOPOETIC TIS SUES, CENTRAL NERV SYS, LIVER &
KIDNEYS. DOSE RELATED REPRODUCTIVE DISORDERS HAVE ALSO BEEN
OBSERVED IN LAB ANIMALS
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid

First Aid:INHALATION:REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT
PHYSICIAN. EYES:FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15
MINUTES. GET MEDICAL ATTENTION. SKIN:WIPE OFF WITH A RAG. WASH
THOROUGHLY W ITH SOAP AND WATER. INGESTION:CONSULT HOSPITAL
EMERGENCY ROOM OR POISON CONTROL CENTER IMMEDIATELY.

Fire Fighting

Flash Point Method:TCC
Flash Point:45.0F,7.2C
Lower Limits:1.2%
Extinguishing Media:USE APPROVED CLASS B EXTINGUISHER OR EXTINGUISHING
AGENTS SUCH AS CO*2, FOAM ETC.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER MAY BE USED TO COOL CLSD CNTNR TO PVNT PRESS BUILD-UP. THIS
PROD WILL FLOAT ON WATER. WATER (SUPDAT)
Unusual Fire/Explosion Hazard:KEEP CNTNRS TIGHTLY CLSD. ISOLATE FROM
HEAT, ELEC EQUIP, SPKS & OPEN FLAME. CLSD CNTNRS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. DO NOT APPLY TO HOT SURFACE.

Accidental Release

Spill Release Procedures:SOAK UP WITH ABSORBANT. DIKE AREA WITH
ABSORBENT MATERIAL. EXTINGUISH ALL IGNITION SOURCES. VENTILATE AREA
TO PREVENT BUILD-UP OF VAPORS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
AWAY FROM HEAT AND FLAME.
Other Precautions:PREVENT EXTENDED SKIN EXPOSURE. PREVENT EYE CONTACT.
DISCARD CONTAMINATED SHOES.

Exposure Controls

Respiratory Protection:USE NIOSH/MSHA APPRVD PARTICLE MASK TO AVOID
BRTHG SPRAY MIST/SANDING DUST IF LOC VENT IS ADEQ TO KEEP TLV W/IN
ACCEPTABLE LIMS. IF LOC VENT IS NOT ADEQ, USE OF NIOSH/MSHA APPRVD
RESP FOR ORG VAP/SUPP LED AIR/SCBA IS RECOMMENDED.
Ventilation:LOC EXHAUST SUFFICIENT TO KEEP TLV & LEL BELOW PRESCRIBED
LIMS. FLOOR VENT SHOULD BE PROVIDED TO PVNT BUILD-UP OF VAPS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EMERGENCY EYE WASH & DELUGE SHOWER WHICH
MEET ANSI DESIGN CRITERIA .
Work Hygienic Practices:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE
REUSE.
Supplemental Safety and Health
FIRE FIGHT PROC:SPRAY OR WATER FOG SHOULD BE USED CAREFULLY IN FIRE
FIGHTING.

Chemical Properties

Boiling Pt:B.P. Text:112F,44C
Vapor Pres:SEE INGS
Vapor Density:HVR/AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:HIGH TEMPERATURES OR FREEZING.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
HYDROCARBONS, TOXIC FUMES.

Disposal

Waste Disposal Methods:DISCARD IN LAND FILL IN SEALED METAL CONTAINERS
AWAY FROM HEAT AND FLAME, IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REUGALTIONS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.